| Customization: | Available |
|---|---|
| Conditions of Use: |
Generator |
| Usage: | Generator |
| Shipping Cost: | Contact the supplier about freight and estimated delivery time. |
|---|
| Payment Methods: |
|
|---|---|
| Support payments in USD |
| Secure payments: | Every payment you make on Made-in-China.com is protected by the platform. |
|---|
| Refund policy: | Claim a refund if your order doesn't ship, is missing, or arrives with product issues. |
|---|
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
The BAC06A Switching Battery Charger is a new switching power supply device designed specifically for the charging characteristics of lead-acid batteries. It is suitable for long-term supplementary charging (floating charge) of lead-acid batteries. The maximum charging current is 6A at 12V and the maximum charging current is 3A at 24V.
Performance characteristics
1. It adopts two-stage charging method (that is, constant current and constant voltage method) to automatically charge, fully charge according to the charging characteristics of the battery, which can prevent over-charging of lead-acid battery and maximize battery life.
2. Suitable for 12V or 24V battery pack charging, the corresponding charger model is BAC06A-12V or BAC06A-24V.
3. With short circuit protection.
4. The charging voltage and current value can be adjusted.
5. Status LED display: AC power indication, charging indication.
6. Adopting switching power supply structure, the input AC voltage range is wide, the volume is small, the weight is light, and the efficiency is high.
Voltage regulation: When adjusting the voltage in the field, disconnect the battery from the charger and measure the output voltage of the charger while adjusting the voltage potentiometer (VOLT) until the appropriate value.
Current regulation: The output is connected to the battery pack. When the charging voltage is not higher than 22.0V (11.0V), the charging current is measured. By adjusting the current potentiometer (AMP), the appropriate charging current is set. The output current can also be estimated by the current potentiometer scale.
5 Operation instructions: 1) Terminals L and N are connected to AC 220V, and BVR1mm multi-strand copper wire is used.
2) Terminals B+, B- are connected to the battery +, - pole, with BVR 1.5mm multi-strand copper wire.
3) POWER: Power indicator, when the charger is working normally, it lights up.
4) CHARGING: Charging indicator, lights up when the charging current is greater than 0.3A.
5) VOLT: Charging voltage adjustment potentiometer.
6) AMP: Charge current adjustment potentiometer.
7) The output insurance FUSE is 10A insurance. After the output is reversed, the insurance will be blown. At this time, there is no output voltage, the output wiring is corrected, and the insurance works normally after replacing the insurance.
8) Replace the insurance operation steps: a) Press firmly with a flat-blade screwdriver and turn it counterclockwise, then pull it out. b) After the pumping, replace the new insurance, and then put it into the fuse holder, then use a flat-blade screwdriver to press it in a small force, and then screw it clockwise. Note: Improper handling or excessive force can damage the seat.
Note: 1) Because the internal output of this charger is connected with a diode and current limiting circuit, this charger can be used in parallel with the charging generator on the engine, and it is not necessary to disconnect the charger when starting. 2) When applied on the generator set, the voltage drop will occur on the charging line due to the large charging current. Therefore, it is recommended that the charging line be separately connected to the battery terminal to avoid affecting the sampling accuracy of the sensor.
Fu'an Shaluo Electronics co.Ltd is a manufacturer of generator accessories, Our company has established a long term and stable business relationship with a number of domestic agents and retailers.
The professional person responsible for the quality of supervision and control in the entire process.
In order to get the superior quality we only use selected good element.
Aimed at enabling the production department to manufacture and assemble the product as efficiently as possible.
Q1. What is your terms of packing?
A: Generally, we pack our goods in neutral white boxes and brown cartons. If you have legally registered patent,
we can pack the goods in your branded boxes after getting your authorization letters.
Q2. What is your terms of payment?
A: T/T 30% as deposit, and 70% before delivery. We'll show you the photos of the products and packages
before you pay the balance.
Q3. What is your terms of delivery?
A: EXW, FOB, CFR, CIF, DDU.
Q4. How about your delivery time?
A: Generally, it will take 30 to 60 days after receiving your advance payment. The specific delivery time depends
on the items and the quantity of your order.
Q5. Can you produce according to the samples?
A: Yes, we can produce by your samples or technical drawings. We can build the molds and fixtures.
Q6. What is your sample policy?
A: We can supply the sample if we have ready parts in stock, but the customers have to pay the sample cost and
the courier cost.
Q7. Do you test all your goods before delivery?
A: Yes, we have 100% test before delivery
Q8: How do you make our business long-term and good relationship?
A:1. We keep good quality and competitive price to ensure our customers benefit ;
2. We respect every customer as our friend and we sincerely do business and make friends with them,
no matter where they come from.
){kind=link}